TALOS C750
Anti-terrorism retractable oil-hydraulic bollard
| Durchmesser | 355 |
| Höhe vom Boden | 1100 |
| Dicke | 30 |
 |
 |
||
 |
 |
 |
 |
GENERAL DESCRIPTION
Security bollard tted with a post, that retracts completely at with the road level, and an incorporated oil-hydraulic motor-pump. Suitable for heavy duty applications being certified and tested in compliance with:
- ASTM F2656-15 C750
- PAS 68:2013 V/7500 (N3)/80
- IWA 14-1:2013 V/7200 [N3C]/80
The bollard is designed and constructed to be able to stop vehicles weighing 7.500 kg, running at a speed of 80 km/h and to absorb at least 1.872.000 Joules of energy, in compliance with the ASTM F2656-15, PAS 68:2013 and IWA 14-1:2013 standards. This bollard is designed for the protection of special areas, such as: military bases, airports, embassies, consulates, banks, prisons, etc. and all those areas requiring a high level of security and perimeter protection.
The bollards is tted with a post (cylinder) rising 1.100 mm from ground level, diameter 350 mm, thickness 30 mm. The post of the bollard (when in fully raised position) remains 50 cm (constraint) inside the enclosure and is supported by two reinforcement plates, the thickness of each is 30 and 30 mm respectively. The post is made of S355K2H steel, the surface is cataphoresis treated and coated by polyester powder; the post of the bollard is well visible in any climate conditions, being tted with an approved, back-re ecting band sticker. The post head is completed with a rubber edge providing protection in case of accidental impacts with pedestrians, etc. The foundation casing is made of treated steel, hot dip galvanized, while the structure of the inner assembly of the bollard is cold dip galavanized.
Post diameter (mm)
Ø 355
Post tickness (mm)
30
Post height (mm)
1.100
Post finish
polyester powder coating
RAL 7016 anthracite grey
Piston diameter (mm)
35
Shaft diameter (mm)
25
Actual shaft travel (mm)
1.115
Frequency of use
intensive (2.000 cycles/day)
Post material
S355K2H steel
Impact resistance (J)
700.000
Crash resistance (J)
2.000.000
Maximun static load (kg)
20.000
Environment working temperature
-20 °C +80 °C
Environment working temperature with heater
-40 °C +80 °C
Rising speed
22 cm/s (~ 5,0 s)
Lowering speed
22 cm/s (~ 4,9 s)
Lowering speed rapid descent system
31,5 cm/s (~ 3,5 s)
68:2013 V/7500 (N3)/80 standards and IWA 14-1:2013 V/7200 [N3C]/80 standards; made up of two oil-hydraulic motor pump
units incorporated in the structure and one oil-hydraulic actuator inside the rising cylinder. Designed to stop a vehicle of 7,5
t at a speed of 80 km/h and remain perfectly intact and operative for the protection of sites under risk of attack and all those
areas where a high level of security and perimeter protection are required in case of a terrorist assault. IP 67. The height of the
rising cylinder (from ground) is 1.000 mm. Rising cylinder made of S355K2H steel, thickness 20 mm, cataphoresis treated and
powder coated. AISI 304 brushed stainless steel cover sleeve available for the rising cylinder. Rubber ring on rising cylinder
head with 12 signalling LEDs with flashing light. Cataphoresis treated aluminium cover, finished to provide a slip-proof
treading surface. Rising cylinder fitted with high intensity, microprismatic, retroreflecting approved sticker (h 80 mm). Hot
dip galvanized steel casing for ground foundation. Impact resistance 700.000 J, breakout resistance 2.000.000 J. static load
max 2.800 kg in standing position, max 20.000 kg in lowered position. Working temperature -40 °C +80 °C. Supply voltage
230 Vac ± 10%, 50 Hz. Absorbed power 3.100 W. Connector and junction box IP 66 for cabling. Rising time ~ 5,0 s. Frequency
of use 2.000 cycles/day. Hydraulic device locking the bollard in standing position.
